Aug 24

Roof Repair, Installation& Replacement Services

Table of content

How to Repair Rolled Roofing
Roof Installation Expertise
Services for Roofing Repair

To keep your home comfortable for your family and pets, you must have a roof over your head. A leaking roof can allow water to enter your home and collect in places it shouldn’t, causing mould and other issues. A damaged roof can also cause damage to other parts of your home. Roof repair is critical when it comes to keeping your home in good working order.

How to Repair Rolled Roofing

Things You’ll Need:

Cats claw nail remover
Hammer
Roofing tar
Wooden stick

Roofing materials, such as felt paper come in a variety of shapes and sizes. Felt paper used on a roof is commonly referred to as rolled roofing. This is because the material is delivered on a roll, rolled out on the top. Your roof will begin to leak if the rolled roofing is damaged. The rolled roofing will need to be replaced to fix the leaks. You will, however, need to purchase a roll of rolled roofing from a local home improvement store.

Step 1

Locate the section of roller roofing that needs to be replaced from the roof. With the cat claw nail remover, remove the nails used to secure the material to the top.

Step 2

Place the tool’s tip against the nail head’s edge. With the hammer, tap the tool’s end to force it up and under the nail head. To remove the nail, pull down on the device. Replace the other pins that were used to secure the material to the roof and repeat the process.

Step 3

Remove the old rolled roofing material by rolling it up and throwing it away. Carry the new roll of material to the top of the building.

Step 4

Place the roll and the roof’s far end together, then start rolling it out. Slide the material’s top edge under the existing rolled roofing.

Step 5

Apply roofing tar or cement to the rolled roofing’s backside. This will aid in the material’s attachment to the roof. Apply the roofing tar with a wooden stick.

Step 6

With the hammer, drive a nail every 12 inches around the perimeter of the roller roofing.

Step 7

Apply more roofing tar where the material’s top edge meets the existing material. This will aid in the prevention of leaks.

Nonetheless, it is still of best value if you hire a professional roofer to repair your roof, saving you energy, money and time.

Roof Installation Expertise

All roofing will not last forever, and most will need to be replaced within 15 to 25 years of installation. Palmetto Roof Installation Expertise Outdoor Solutions’ licensed roofers will begin by removing the roof down to the deck and inspecting the structural integrity of the home or business. Following that, we will not only install new roofing, but we will also replace the flashing and ensure that your roof is adequately ventilated. All of those particulars are in our capable hands. Our expert roofing crew will install all types of roofs, including the following:

Asphalt Roofs – These roofs are commonly used in residential areas and are made of shingles. Asphalt shingles are incredibly durable and come in a variety of colors. This type of roofing is also suitable for use in the commercial sector.

Metal Roofs – These roofs do not appear to be metal and instead resemble asphalt shingles, shake, and slate. These roofs are popular in both commercial and residential applications.

Rubber Roofs – This option is commonly used on commercial buildings that are flat or have a minimal slope. Rubber roofs are also widely used for home additions such as a sunroom or porch.

Shake and Slate – Cedar shake is a popular roofing material among homeowners. Although shake and slate roofs are more expensive, they have a stunning appearance.

Services for Roofing Repair

Not all damaged roofing needs to be replaced. Quite often, a simple roof repair can solve a problem. This type of work should not be performed by anyone who is not a trained professional. That is when you should contact Palmetto Outdoor Solutions.

An experienced member of our roofing team will come out to your home or business and assess the problem. Before making any repairs, we will inform you of what needs to be done and provide you with a free estimate. These repairs could include replacing broken shingles, repairing flashing, or addressing general wear and tear.

Aug 19

Roof Installation Services That Are Guaranteed to Last

By remadm | Roof Installation

Roof Installation

Understanding the roof installation process and steps will help you ensure your new roof is properly installed, whether you hired a professional or plan to do it yourself. Here’s a quick rundown of how to install metal roofing and asphalt roof shingles.

Get the best price, get roofing price quotes from at least four pre-screened and licensed roof repair and installation professionals before beginning your project. To get an idea of how much your roofing installation will cost, use our contact form and talk to local contractors.

You will better understand the process if you know what to expect from your roof installation. When your roofing contractor comes to install or replace your roof, here’s what you can expect.

Remove the Old Roofing

Before the new roofing material can be installed, the old roofing will most likely have to be removed. Many people will layer multiple roofing layers on top of one another to save time, but too many layers (such as asphalt shingles) can cause the roof to fail prematurely. The old roof should be stopped and rebuilt down to the sheathing.

Evaluate the Roof

Examine the sheathing after removing the old roof. Roof sheathing is made up of flat panels that serve as structural Remove the Old Roofing support and a foundation for roofing materials such as shingles. Look for any damp or troublesome areas that will need to be replaced.

Protect Against Ice

Suppose you live in an area where ice forms for even a portion of the year, an ice and water barrier should be installed around your roof. This product is applied to the roof’s edges, particularly the very bottom edge, which is the most prone to ice buildup. This sticky underlayment adheres to the roof sheathing before being nailed down with roofing nails for added strength and stability.

Put on the Drip Edge

The roofing drip edge is installed in two parts of the roof installation. It goes on before the underlayment on the lower part of the roof and after the underlayment on the sides of the roof. Install the metal drip edge over the ice and water barrier along the bottom border of your home first. Nail it flat against the roof with a nail gun.

After you’ve installed the roof underlayment on your home, you’ll need to go over it with a drip edge on the sides, just as you did at the bottom. This keeps water from running over the siding’s edge and back underneath it.

Roofing Underlayment Installation

Whether felt paper or synthetic, Roof underlayment is saturated in water-repellent materials and is available in two thicknesses: 15# and 30#. Although the 30# underlayment is twice as durable as the 15#, the synthetic products outlast both felt paper options. Invest in the more expensive synthetic underlayment if you want the most effective way to protect your roof aside from the roofing itself; it’s the most convenient and durable option.

Roll the underlayment along the roof’s edge and secure it with cap roof nails every four inches on the outside edges and every eight inches in the center. Instead of going through the drip edge, these cap nails should sit just above it.

Roll out one row of roofing underlayment at a time, securing it all with roofing cap nails and ensuring that the lower row overlaps the next row by at least six inches. Install a row straddling the peak of the roof so that the underlayment caps off both sides of the roof at the same time.

Aug 18

Protect Your Fascia Boards From Water Damage With Fascia Wrap

By remadm | Soffit & Fascia

Soffit And Fascia Repair Contractors Near Me

What Is a Fascia Board, and How Does It Work?

Fascia board is the wood trim that runs along the edge of your home’s roof. The main goal is to protect the exposed opening left by your rafters on your roof. Animals, water, and bugs would get into your roof and attic if you didn’t have a fascia board. This wood is highly vulnerable to the water damage caused by water leaking behind gutters. It always rots and deteriorates over time. The drains will eventually collapse. Typically, the fascia is attached to the rafters first, followed by the gutter.

Pro Tip: If your gutter hangers can hit the rafters, the gutter and fascia will never come loose like in this photo.

Cladding or Wrapping Your Fascia Board

Wrapping metal around your existing fascia board and roofs is known as fascia wrapping or cladding.

It provides an exact colour and material match when installed in conjunction with new Rain Gutters. Wrapping your wood fascia boards in aluminum, copper, or steel has a lot of appealing features.

The Metal Fascia Wrap Protects your wood from the effects of the UV rays.
It provides a Barrier from the wind-driven rain.
It requires no Painting. (When a house is painted, many people have their gutters removed so that the wood fascia boards underneath can be painted. Usually, the painters are unable to reinstall them correctly.)
It helps to minimize some areas that insects can usually penetrate the wood.
Provides an exact colour match when installed together with new Seamless Rain Gutters.

If your fascia boards are wavy or warped, we may need to install more than one seam per 10 feet. All Fascia Wraps come in 35 different colours, as well as Copper and Stainless Steel.

Fascia Wrap Installation

We use a “Break” to bend the aluminum into a shape that fits around the fascia board. It’s the same machinery that is used to bend custom siding for home exteriors.

Fascia Wrap That Bends

First, we’d measure and cut the aluminum into 7-inch strips for the 16-inch fascia board. (9′′ for 18′′, 11′′ for 110′′, etc.) After that, we’d measure and score a new line at the 1-inch mark, then break or bend the aluminum into a 90-degree right angle.

Pre-bent Fascia Wrapping Ready to Install

Once you bend all of the aluminum fasciae wraps to shape, you are ready for the actual installation. You can wrap your current fascia board or apply fascia wrap to a new fascia board that has been put on your home.

Remove all gutters and hardware if you’re wrapping an existing fascia board. Any nails, screws, debris, or other objects that could prevent the wrap from sitting flush against the wood should be removed from the fascia. Finally, place the wrapping on the fascia so that the 1-inch portion extends past the fascia board’s top edge. Use screws to secure the wrap to the fascia board.

Installing New Fascia, Fascia Wrap, Drip Edge, and Soffit

The first step in installing a new fascia with fascia wrap is to remove the existing fascia board and all nails, screws, and hardware. The new fascia board would then be installed without the wrap. Finally, wrap the fascia wrap around the new fascia, ensuring that it covers all of the wood, and screw it in place. You’ll be able to see what you’re doing this way.

The Fascia Wrap and Drip Edge Collaborate

Drip Edge

The drip edge is a long right-angle strip. The gap between the roof and the gutter that it covers can be seen. The drip edge is an essential part of the gutter system. Its job is to keep the gap between the shingles and the gutter closed, preventing water from getting behind the gutter. Additionally, it directs water into the gutter. The Drip Edge directs the water into the gutter’s center. The drip edge closes the gap between the roof deck and gutter beneath the shingles, keeping water from getting behind the gutter and under the shingles. Fascia capping, on the other hand, only protects the fascia. Water can still get behind the gutter and into the walls without a drip edge. The Fascia Capping would still protect your fascia. If you only have one option, the drip edge is far more important.

A WARNING REGARDING DRIP EDGE…

Suppose you have Fascia Wrap on your home or are thinking about getting it. There is one important point to remember. If you have fascia wrap, you must have a drip edge appropriately installed. The drip edge should be appropriately installed on all homes, but it is essential with fascia wrap.

When you wrap your fascia, you can’t see the wood because it’s completely covered. As a result, you won’t know if the wood is rotting until it’s far too late. Typically, the gutters are the first to become loose. The fascia wrap is then separated from the fascia board. The fascia wrapping and a shard of fascia hanging from under the gutter are visible in the two photos below. This fascia board has rotted and disintegrated. Because there is no wood behind it, the gutter is basically supported by the downspout at this point.

Behind the fascia wrap, the fascia board rotted away. Nobody realized there was a problem until it was too late because of the wrap. The photos above were taken one month before the photos below.

To be clear, the above home did not have a drip edge installed throughout. Water was leaking behind the gutter, destroying the fascia board. The fascia wrap was installed without a drip edge, and the result was a complete disaster.

Wrap Your Rake

They’re very similar to the fascia board. They fill in the space left by the rafters. The difference between a rake board and a fascia board is that a rake board is slanted while a fascia board is straight. Rake boards never have gutters because they are always inclined.

Wrap your rake board in the same way you wrapped your fascia board. The rake board will be protected in the same way as the fascia board, extending its life by two to three times.

Conclusion

Wood rot on a fascia board in its early stages.

We always recommend wrapping only new wood. If you wrap wood that is more than ten years old, it may begin to deteriorate in a few years, and you will not notice until it is too late. Adding wrap to an old fascia board is not a viable option for extending the life of the fascia.

Wrapping your fascia board can extend the life of your board by two to three times. On the other hand, wrapping will exacerbate the problem if you don’t have a drip edge. As a result, ensure your fascia wrap and drip edge are installed and configured correctly by a professional.

After making any repairs to your roofing edge and gutter system, keep an eye out for anything that doesn’t look right. Call us at Remember me roofing for needs.

Aug 16

How Often Should You Replace Your Roof?

By remadm | Roof Replacement

Ready to learn more?

Average Lifespan of a Roof

The lifespans of different types of roofs differ. So, to begin, we’ll list our best guesses for average roof lifespans based on the roofing material.

Asphalt Shingles

On the other hand, architectural asphalt shingle roofs have a design that makes them more resistant to the elements. Roofs with three tabs should last 15-20 years under normal conditions before they need to be replaced. 3-tab asphalt shingle roofs can last up to ten years longer.

Clay/Cement Tile Roofing

One of the most durable roofing materials available is clay/concrete tile. The tiles are not only highly durable but also quite heavy. This means they’ll be installed on top of extra-durable roofing reinforcement, giving your home even more protection.

As a result, tile roofing is exceptionally long-lasting, lasting anywhere from 50 to 100 years.

Slate Roofing

Slate is the most long-lasting roofing material. It will, in most cases, last 100 years or longer.

Wood Shingles

Wood shingles have a 25-30 year average lifespan. They do, however, necessitate maintenance, which reduces their useful life.

If you don’t keep your roof free of leaves and moss, moisture will be trapped against the roofing, which will lead to decay. However, if you maintain your wood shingle roof properly, it could last for 50 years or more.

Fire can also damage wood roofing. As a result, it is dangerous and illegal to install in specific locations because it can easily catch fire.

Wood Shakes

Wood shakes are more resistant to UV rays and harsh weather than shingles due to their thickness. Roofs like these are expected to last 35 to 40 years.

However, upkeep is a consideration. A wood shake roof’s lifespan is determined by how well it is maintained.

Metal Roofing

Another extremely durable roofing option is metal roofing. Steel and aluminum, which are common metal roofing materials, should last for 50 years before needing to be replaced. Zinc and copper roofing, for example, can last for 100 years or more.

Other Factors That Affect Roof Lifespan

Your roof’s lifespan is influenced by factors such as maintenance and weather, including the materials. Certain weather conditions, for example, may make wood shingles more susceptible to mould and crack. Sealant erosion can occur on even the most durable metal roofs over time.

In addition, because asphalt shingles are very light, they are more likely to come loose in areas where high winds occur frequently. Trees or tree branches can also be knocked into the roof in windy areas with a lot of foliage, causing damage.

Moisture can seep into the roofing material through a small crack. Temperature changes cause the crack to widen as it expands and contracts. Furthermore, if such damage is not addressed promptly, it will deteriorate rapidly.

If you’re looking for a professional roof inspector, contact Remember Me Roofing today to ensure your roof is performing at its peak!

Aug 12

Metal Roofing for Your Home

By remadm | Metal Roofing

Table Of Content:

Metal Roofing Benefits and Advantages
Eco-Friendly

Whether you notice them or not, metal roofs are everywhere. You probably wouldn’t usually think to look at the roof on a home, but if you take a drive down any road in any city, you’re likely to find a house or building donning some kind of metal roof.

But how much do you know about metal roofing? Did you know that it often requires little to zero maintenance after it’s installed? Or that you can choose from a variety of looks and styles, like standing seam or stamped metal roofing?

Remember Me Roofing wants to assist you in selecting the best roof for your needs, which is why we believe that explaining the basics of metal roofing will help you make an informed decision. We will discuss the following topics in this article:

Metal Roofing Benefits and Advantages

There are several advantages to metal roofing over other roofing materials such as asphalt shingles, tiles, or concrete. While metal roofing may be the best option for some homeowners or business owners, we recognize that it is not the best material for everyone. Consider some of the most common reasons people purchase metal roofing to determine if it is a good fit for you:

Longevity

Metal roofing is precisely engineered to outlast any other roofing material by decades. Many customers choose a metal roof because it will be the last roof they will ever need to install on their home or business. Most metal roofs last 60+ years without showing signs of deterioration or corrosion, depending on the type of metal material used.

Durability

When comparing the strength and durability of various materials such as wood, concrete, metal, plastic, and glass, metal easily wins out. Metal roofing, when properly installed, is designed to withstand strong winds, Debris (leaves, sticks, etc.), Rain, Snow, Hail, Mold, Mildew, Rodents and other animals.

Furthermore, metal roof materials are frequently Class A fire-rated and noncombustible, indicating the highest level of fire resistance available. One of the main reasons for the popularity of metal roofing is its proven durability against common roofing threats.

Maintenance

The amount of maintenance required to keep a metal roof in good shape is usually minimal, especially if the roof was installed correctly. Looking for leaves, branches, and other debris that could get stuck on the roof and in the gutters twice a year and after solid storms would be part of general upkeep. There are methods to clean your metal roof if dirt or other stains do not come off with rain. In addition, a concealed fastener metal roof requires less maintenance than an exposed fastener metal roof.

Eco-Friendly

What is the definition of a metal roof? Types, Applications, and Definitions: Eco-Friendly Metal Roofing eco

Metal roofing is environmentally friendly for a variety of reasons.

Most metal is highly recyclable, which means that scrap metal, old panels, or even manufactured excess scraps can be recycled and reused in future products. These metals are available as either pre-consumer or post-consumer recycled content:

Scrap metal from the manufacturing stage that has been recycled for future use is known as pre-consumer recycled materials. Excess materials that have previously had a consumer and have been recycled for reuse are post-consumer recycled materials.

Second, some metal roofing materials, such as aluminum, are made entirely of previously recycled metal. Almost all aluminum roofing is made from recycled materials, accounting for nearly 95% of the total.

Third, many metals, such as zinc and copper, can be naturally replenished and sustained over time because they are found in the environment or the Earth’s crust. Make sure you specify that recycled content is essential to you before construction and installation.

The variety of warranty options provided by metal manufacturers or suppliers is one of the best aspects of owning a metal roof. Weathertight warranties, which cover leaks in the roofing system, and paint warranties, which cover specific levels of degradation of the paint system applied to the metal substrate, are two of the most common. Warranties vary widely depending on where you live, the climate to which the roof will be exposed, the type of roofing material used, and the type of coil paint system used. Before you buy, make sure to read the warranty documents thoroughly and ask questions.

Note: Weathertight warranties are typically used by architects and building owners of non-residential structures to ensure the system manufacturer’s long-term integrity.

Aug 09

Pros and Cons of Exterior Siding

By remadm | Exterior Siding

Exterior siding is a material applied to the outside of a building to protect it from the elements, prevent heat loss, and visually unify the facade. Siding refers to wood units or products that look like wood that is used on houses. Clapboard, horizontal lap siding, vertical board siding, and shingles are just a few examples of siding. Board and batten siding differs from clapboard in that it consists of vertical wood boards with their butt joints covered by battens (narrow strips), giving it a seamed appearance. It is sometimes found in Carpenter Gothic houses and very modest structures. Aluminum and polyvinyl-fluoride-coated siding (commonly referred to as vinyl siding) were created as low-maintenance alternatives to wood clapboard. Fibreboard, a pressed-wood-pulp product, is occasionally used, despite its limited long-term durability. Cladding, which can be made of brick, glass in a metal framework, or panels made of stone, concrete, metal, or other materials, is used to cover the exterior of larger buildings.

What type of siding is the cheapest?

Vinyl siding, which is both cost-effective and versatile, is still the most popular siding choice in the United States and Canada. It’s so popular because it’s the most cost-effective siding option, making it accessible to even the most frugal homeowner. Vinyl siding comes in an almost infinite variety of colours and styles and is extremely low-maintenance and simple to care for. Vinyl siding prices vary, but you should expect to pay between $2 and $5 per square foot to have it installed. Vinyl material should cost $1 per square foot or less.

Your total installation cost will depend upon the thickness and quality of a particular siding product, with thinner options often costing significantly less than thicker, higher-quality panels.

Cheaper panels offer short-term savings because they are more likely to crack, tear loose from your home’s exterior, or sag, resulting in higher replacement and repair costs. For better installation results, look for an Exterior siding installer near you.

Pros

Vinyl siding can imitate a wide range of more expensive options because it is an artificial, fabricated material. As a result, it works well with a wide range of architectural house styles, from modern to ornate Victorian to distinctive Craftsman. It enhances curb appeal; the panels are lovely up close and from a distance since the colour runs through them. There will be no peeling, flaking, chipping, or scratching! Since the colour goes through the material, it won’t fade or dim over time. Over 300 vinyl siding colours meet or exceed industry colour retention performance test criteria.

Vinyl siding provides a wide range of customization options for your home. For your windows, doors, and other surfaces, choose from various trim, styles, textures, shapes, and decorative accessories. You’ll also be able to choose from over 300 long-lasting colours. The siding of this type is durable and long-lasting. It resists denting (though we don’t recommend hitting it with hockey pucks or golf balls. It’s not indestructible; it’s dent-resistant.) Wind, heat, cold, and moisture have virtually no effect on it. There’s no need to worry about warping, splitting, rotting, or insect damage.

To maintain its appearance, vinyl siding does not require scraping or painting. To remove most dust and debris that has accumulated over time, rinse it with your garden hose. If you encounter particularly stubborn soiling, use some mild soap with that water.

So forget about awkward, fear-of-height-inducing ladders and wasting weekends doing maintenance!

Cons

There are several significant drawbacks to vinyl siding. It doesn’t have the same longevity as more expensive materials. It has a proclivity for fading, cracking, and buckling, particularly in areas where the weather is consistently bad. When heated to high temperatures, the material is known to emit pollutants that are harmful to the environment. When put under stress, vinyl will bend or crack, necessitating the replacement of the siding. It conceals moisture issues that can lead to the growth of mould in your home. When installed, less expensive products have an unsightly visible seam. Finally, vinyl is one of the least environmentally friendly materials available; it cannot be recycled and thus pollutes the environment.

Bottom line:

Due to its lower cost than other materials, vinyl siding will continue to be the most “popular” of all home siding options. Vinyl exterior siding lasts a long time. Depending on the quality of the materials and the contractor’s experience that installs it, it can last about 60 years. And with some minimal maintenance on occasion, your vinyl siding can last even longer than that.